specifications at the end of the Operation Manual. Since the service life of The main unit for the HVS series is HVSHS. The following. For-a Hvshs Manual. HVS / – HD/SD Portable Video Switcher, HVS- – 3G/HD/SD 2M/E Video. Switcher, HVSHS – HD/SD M/E Video. A HVSHS Type A M/E Switcher featuring 8 HD/SD-SDI Inputs HVS- 35OU M/E Control Panel; Manual; AC Cord; Rack Mount Brackets; BNC Cable .

Author: Kelrajas Tejar
Country: Haiti
Language: English (Spanish)
Genre: Business
Published (Last): 5 January 2012
Pages: 391
PDF File Size: 3.31 Mb
ePub File Size: 15.62 Mb
ISBN: 586-7-39386-519-2
Downloads: 68826
Price: Free* [*Free Regsitration Required]
Uploader: Vushakar

Mmanual begins the current frame. Setting Up Additional Inputs How to Verify Version Externally created still data can be sent to the main unit via Ethernet. USER Button User buttons can be assigned to specific menu pages and used as shortcuts or specific functions buttons. Output signal Pin No.

Check to ensure no damage has occurred during shipment. Signal ground The pin assignment shown above is the factory default assignment. About This Manual This manual is intended to help the user easily hvs-350hz the Hanabi series switchers and make full use of their functions during operations.


Be the first to review this item. Playing Back Sequences Using Advanced Settings Playing Sequences by Changing Bus Signal Selections Sequence data includes that on bus signal selection states and are basically recalled on the control panel exactly the same that they were stored.

Saving and Loading Crosspoints A set of all crosspoints destination and source pairs on the router can be saved to and loaded from the hv-s350hs. The indicator blinks red when an alarm occurs. Transfer of the externally created data to the main unit is possible by the 4 still store channels via Ethernet.


Move the joystick up, down left and right to move the crosshair cursor onto the desired color.

For.A HVSHS Type A M/E Switcher HVSHS TYPE A B&H

manial Then configure the RS port as in the procedure below. On-air Tally The tally indicates which video is currently On-air output from the program and which video is set to be the next output.

Refer to the Audio Mixer user’s manual to connect the cable to the audio mixer.

In this case, you will need to limit the fader range. The following example shows how to setup and perform the Crossfade Transition of PinP1.

Advanced Example 1 using Key Insert Aux Lit orange, Performs the user transition for KEY. Pattern Modify Example2 Pattern Loading Setting Data ON. User names can be given to input signals, internally generated black matt and matt signals, and still pictures. Mask And Invert It takes about 1 minute to complete receiving data. Refer to your router’s User Manual for how to set up the router.

Page Crosspoint Switch Timing The picture can be manul, shrunk, repositioned, cropped or given a hvs-350hx. Key And Dsk System Signal Format Selection at the Initial Use When first switching on your unit, please select a signal format as shown below. It is used to synchronize asynchronous signals.

With the addition of the AUX assignment function, all the channels from input to output can now be checked on the multiviewer. Quick Recall direct Mode The preview bus output can be assigned to, however, an auxiliary output.


FOR-A HVS-350HS Operation Manual

These control methods can exist together in the same system. See the figure and the table below. Other Menu Access Buttons By pressing once or twice specific buttons in the bus select section or transition control section, the related menus can be displayed.

Event Operation This section shows how to store and load events. Page Tally Control Example The setting example in the table below shows how to make tally settings in the following conditions. When performing transitions mix or other there may be times when you want the transition to the next signal to only complete to a certain degree instead of fully switching from one picture to another.

A delay line with the clip memory can delay an output video up to 30 frames. Changing Settings or Values by Using the Numeric Keypad Users can also use the keypad to input numerical settings to a menu.

This section explains how to setup and display PinP pictures as shown in the manaul below as an example. The operational example below shows how to create a sequence having 5 steps with the first and last steps the same.